As more and more vehicle owners have converted cars into "sanitation garbage trucks, sprinklers, and suction trucks, etc.," the potential safety risks have also increased substantially. Some of the irregular modifications have led to a decrease in the service life of the car. The following garbage truck manufacturers introduce some ten tips for garbage truck modification. 1. After the chassis has been modified, the axle load on the front and rear axles must not exceed the maximum axle load quality allowed on the chassis. The total mass of the second and third rounds of garbage truck products shall not be greater than the maximum load quality calibrated by the chassis used, nor shall it be less than 90% of the maximum allowable total mass. Third, all modified vehicles and changes to garbage trucks should be implemented in accordance with the current national regulations. Fourth, the refitting manufacturers shall be responsible for the design, manufacture and safety of all refitting devices; and shall be responsible for the correctness of connection between the refitting part and the chassis carrying system and the power output system, and shall not affect the entire car due to the general layout design of the refitting part. safety. 5. The conversion plant shall not dismantle, change, weaken and destroy the original structural components of the chassis for the purpose of installing the modified parts, or cause the chassis to be heavily loaded with stress concentration. Sixth, the modified part should have enough space for maintenance, so that the relevant parts of the inspection, maintenance, lubrication, replacement and disassembly have a good proximity. When necessary, the compartment car chassis must have a corresponding maintenance activity cover. 7. After the refitted vehicle is driving on the vehicle, and the refitting part is in any motion state, it shall be ensured that friction, collision and interference do not occur between the refitting part and the original chassis member. 8. Pay attention to reduce the height of the center of gravity of the converted part (including the bearing quality) as much as possible and ensure that the axle load distribution of each axis does not exceed the maximum allowable shaft load of the plant to avoid the eccentric load between each axis and the left and right wheels. 9. When the selected chassis is a turnable cab, the cab shall be smoothly turned after the conversion. 10. It is not allowed to affect the running brake and steering performance of sanitation vehicles due to modification.
1. Usage: QZK-D Program Control Paper Cutting Machine is used to cut the printing paper
of various kinds, paper products, plastic, thin film, leather, slice of
non-ferrous metal, etc.
2. 8inch computer keyboard : this series of program controlled computer adopts
industrial human-machine interface, the main part of the computer is industrial
chip fromAmerica.
it has six languages, USB interface and hand wheel encode, which is easy
to operate. it can self-diagnose the malfunction animation operation mode. the
program memory can store 5000 programs , each of them can save 999cutting 's
datum of different locations. its storage hours are over 300,000 hours, which
ensure the reliability of the performance. paper delivering motor is Japanservo motor , its work speed is 6-18m/min. And the position accuracy
can be 0.01mm.
3. single Hydraulic Device: the hydraulic system adopts theGermanyadvanced technology.
Equipped with combined hydraulic valve, double hydraulic controlling structure,
it approves hydraulic device greatly. The hydraulic device pass CE certificate.
4. Double Guide Device: the paper pusher adopts double imported linear guide and
roller ball screw.,which can prolong the machine use life, and can bear the
high speed paper delivering.
5. Photo cell: it is equipped with a photo cell safety protection
device.
6. Over load protection device; convenient knife changing
device.
7. Worktable chrome treatment: the worktable and side board surface are all adopted
chrome treatment to improve the precision and quality of the machine.
8. Air ball: air
balls are installed in the worktable. The paper sending work will be easy and
accurate.
9. Cutting controller: both of the user`s hands operate the machine. It can cut
paper in one time.
10．Electronic knife lock: when the
machine is malfunction, the electronic knife lock will lock the knife, and the
machine will stop cutting to protect safety.
11. Safety notice & Glass covers: the machine has passed CE certificate. All the safety
notice and direction mark is used to cause the safety attention of the user,
and do protection and maintenance in time.
12. Main electric device are imported fromGermany,
French,Japan,
etc.
Automatic Paper Cutting Machine, Programmed Paper Cutter, Program Control Paper Cutting Machine Anhui Innovo Bochen Machinery Manufacturing Co., Ltd. , https://www.innovomachines.com