The continuous increase in the cost of vehicles has forced people not to miss the details of any savings. Tires are actually a consumable material that costs a lot during the car's use. The four tires are worth several thousand yuan. If they are used improperly, they will cause abnormal wear and tear, which is also a test for the owner's wallet. How to reduce tire wear and maximize the service life of the tire is the knowledge that the owner must master. Good and skilled driving techniques can effectively reduce tire wear, extend the life of the tire, and improve driving safety. Insufficient or too high tire pressure can easily lead to puncture "On the high-speed must refuel the tires." Many riders believe that the high-speed gas should be enough, the car has "strength" to run high-speed, "but in fact, this idea is wrong. Dongfeng Fengshen 4S According to the shop staff, tire pressure is too high and the contact area between the tire and the ground will be reduced, and the pressure on the tire will be relatively increased, and the tire's grip will be affected, and when the vehicle passes through a trench or bumpy road, There is not enough space in the tire to absorb the vibration, in addition to affecting the driving stability and ride comfort, it will also increase the impact on the suspension system, which will also bring harm. When the tire pressure is lower than the standard value, the tire tire The wear of the shoulder increases sharply; when the tire pressure is higher than the standard value, the ground contact area of ​​the tire decreases, the unit pressure increases, the wear of the middle tread of the tire increases, the rigidity of the tire increases, and the dynamic load of the wheel is increased. Produce a carcass burst.The start must not be too fierce, to avoid frequent use of brakes and emergency brakes, so as to avoid tires and the ground to accelerate the tread wear; in turning the car, overtaking, pass When crossing intersections, narrow roads, railway crossings and other areas, it is necessary to grasp appropriate speeds and pay attention to the dynamics of roads, pedestrians, and vehicles, prepare for braking, reduce frequent braking, and avoid emergency braking, thereby reducing tire wear; When it is impossible to avoid the broken glass or other foreign matter, it must be decelerated. Do not slam the brakes. The pressure caused by the sudden brake increases, and glass fragments and foreign objects can easily enter the tire. Check the tread for cracks "I have a glass on the side of my tires. Is there any problem with running at high speed?" asked the owner. 4S shop staff introduction, the tire side of the injury, the insurance factor can not be guaranteed, because the side of the tire is basically no steel wire, the tire wall is very thin, high-speed easy to puncture. Regularly check the tire surface for cracks, deformation, and other defects. The groove of the tire gradually becomes lighter due to wear and tear. If it wears flat, it will lose the effect of drainage and slippage. The performance of the car will be greatly reduced, and the seemingly small cracks are the hidden dangers of puncture at high speeds. Pay attention to remove small stones in the groove in time. Avoid parking your vehicle on rough, sharp or sharp stones. Vehicles should not be parked near or in contact with petroleum products, acids, or other materials that affect the deterioration of rubber. The driver should not turn the steering wheel after parking. Such operation will accelerate the wear of the tire. The tires tend to overheat in the summertime when they are driving for a long time or when they are driving at high speeds, and the air pressure increases. At this time should stop cooling, is strictly prohibited deflation pressure or splash water cooling, to prevent the abnormal aging of the tread rubber. Usually pay attention to the good habits of the road than usual maintenance The auto repair staff introduced that when driving in the road maintenance construction section, the method of slowly selecting the road surface should be adopted to prevent the tires from being excessively knocked and even stabbed or scratched; in the case of uphill roads, one must select the road surface. ,Reducing the impact of tires and roads, to avoid damage to machinery and tires; Second, to slow down, to avoid tire bumps and strong vibration; Through muddy sections, should choose a more solid, non-slip place to pass, so as not to tire sagging, in situ Idling and severe heat generation caused severe cuts and scratches on the tires and the sidewalls. The turning of the vehicle should be based on the curved road conditions and the turning radius. Generally, the speed should be decelerated appropriately to avoid acceleration of unilateral tire wear due to inertial force and centrifugal force. When the vehicle is descending, appropriate speed should be controlled according to the size, length and road conditions of the slope. This can avoid or minimize the use of emergency braking to reduce tire wear; vehicles parking on the way and stop at the stop should develop the habit of safe gliding. In the maintenance and use of tires, do not forget the most important tire - spare tire. Reserve tires are factory-fit, but they are often forgotten by the owner and lack maintenance. It is recommended that the owner periodically check the spare tire every 3 months and inflate it if necessary so as not to find it flat when it is needed. WANLONG CHEMICAL CO., LTD , https://www.wanlongpigment.com