There are many users when they purchase a beekeeping vehicle. Because local manufacturers do not produce such vehicles or because the price/performance ratio of such vehicles is not very high in the local area, many people will choose to purchase goods from other places. Generally speaking, the procurement of apis in foreign markets will almost always be done in the cities where the vehicles were purchased. In the past, where the vehicles were purchased, they would return to the place where the vehicle was purchased last year when they were inspected last year. With the opening and change of national policies, it is no longer necessary to worry about the annual inspection of cars purchased in other places. It is possible to carry out annual inspections in other places. Then how to operate in remote inspections? The picture shows the Chu Feng bread apiculture In fact, it is not difficult to carry out annual inspections in different places. If there is no time available, it is not necessary to go back and forth for oil, tolls, meals and accommodations. The current national network of vehicle information is very convenient when handling households and annual inspections. What documents do you need to provide for remote inspection ? Travel card, copy of insurance policy, original ID card. If you eliminate the violation, you can do an off-site inspection proxy and then you can go to the local inspection. Remember that you must deal with a violation of the law in order to handle the power of attorney. Get your certificate ready to be sent to your landing area in just two days and you can receive an offsite annual inspection proxy. Then, with the annual inspection letter of authority to the local area, the annual inspection can be carried out. The specific cost is based on the local fees. It is a better way to handle the annual review in a remote place than before. What is the method of handling car inspections in different places ? Checking for cars is the same as for other cars, but there are many details to pay attention to. The car inspection process is very simple, you can apply for a car inspection on it. Do not listen to the door inspection cattle, spend money. The following describes the process of car inspection for everyone: Car inspection, first divided into two kinds of companies and private situations. Company card No matter whether the company is on the card or whether it is in the Mainland, it only needs car insurance and household invoice information. Private on the card If it is private, you only need car insurance, household invoice and ID on the local board. If you apply for a vehicle inspection in a foreign country, you must apply for a temporary residence permit to apply for a vehicle inspection. In many places, temporary residence permits are not available, so if you want to go to a different location, you must call your local company name. If there are acquaintances or relatives in different places, they can also go to their names. After the documents are brought up, drive the car to the vehicle inspection center and place the keys on the car. Directly to the vehicle inspection office will be able to pay the vehicle inspection fee. The staff of the vehicle inspection office will open your bee-keeping vehicle for inspection. You only need to wait in the waiting room to check the result of the vehicle and listen to the broadcast message to get your test results. The above is the entire process of the annual inspection of the bee-keeping vehicles in different places. It is actually very simple. It is hoped that some users who purchase beekeeping vehicles in other places will provide some help in annual inspections.
Cross Roller Bearing is a special type
bearing. Because of the inner ring or outer ring were separated, after loading
the roller and the cage, it is fixed with the cross roller shaft ring to
prevent the separation, so the operation is simple when installing the cross
roller shaft ring. Since the rollers are intersected, only one set of cross
roller bearings can withstand the load in each direction, which is three to
four times more rigid than the traditional model. At the same time, because the
inner ring or outer ring of the cross Roller Bearing is a two-part structure,
the bearing clearance can be adjusted, and even if it is preloaded, it can
obtain a high-precision rotary motion. Moreover, because of its special
structure, it is commonly used in industrial robots as joint bearings.
The classification and model series of cross roller bearings are below:
RB type (outer ring segment)
RB series models for cross roller bearing, basic, inner and outer ring
size is minimal to miniaturization, its structure is the outer ring is divided,
the inner ring design is an organic whole, the inner ring spinning of high
precision parts suitable for requirements.
RE type (inner ring segment)
The RE series is a new type of XRB design concept, which is the same size
as the XRB type.The structure of the inner ring is the split type and the outer
ring is one design, which is suitable for the parts with high rotating
precision of outer ring.
RU type (inner and outer circle)
The RU series model is not required to be fixed flange and support base
due to the processing of mounting holes.In addition, due to the adoption of the
integrated inner and outer ring structure of the belt, the installation has
little effect on the performance, thus achieving stable rotation precision and
torque.Can be used for outer ring and inner ring rotation.
RBC type (outer ring segment)
The RBC series model (corresponding to the CRBC series of IKO company) is
composed of the outer ring is the split type, the inner ring is one design, and
the belt is fully loaded with roller bearings.Suitable for high rotation accuracy
of inner ring.
CRBH type (inner and outer ring)
CRBH series model, outer ring and outer ring are integral structure, used
for outer ring and inner ring rotation.
RA type (outer circle segmentation, ultrathin type)
The RA series model is the compact type that reduces the thickness of RB
and outer ring to the limit.Suitable for areas with light weight and compact
design, such as rotating parts of robot and manipulator.
SX type (outer ring segment)
The structure of SX series is similar to that of RB series. The outer ring
is a two-part structure, which is designed with three spring card rings and the
inner ring, which is suitable for the place where the inner ring has high
rotation precision.
XRU08 type (inside and outside)
XSU08 series is similar to the RU series, and the inner and outer rings
have been machined with holes, so no fixed flange and support seats are
required.Due to the adoption of the integrated inner and outer ring structure,
the installation has little effect on the performance, thus achieving stable
rotation precision and torque.Can be used for outer ring and inner ring
rotation.
We believe that we can supply the best service and price for your, hope to make a long-term cooperation with you. If you have any question please do not hesitate contact with us. We keep warmly welcome you visit us in any time.
Cross Roller Bearing Cross Roller Bearing,Excavator Parts Cross Roller Bearings,High Precision Cross Roller Bearing,Thin Section Cross Roller Slewing Bearing LUOYANG AUTO BEARING CO.,LTD , https://www.ballbearing.nl