In May, more than 800,000 domestic automobile recalls exceeded 15.80%

Recently, according to the recall announcement issued by the AQSIQ official website, Gasgoo has compiled the recall of domestic cars in May 2018. The results show that in May of this year, there were 16 announcements concerning car recalls involving 15 auto companies. 21 The number of recalled models totaled 825,846 vehicles, and the number of recalls increased by 21.16% from the 680,000 vehicles in April. In April, the recall of Takada's airbags, which exceeded 600,000 vehicles and accounted for 95.33% of the total recalls, achieved a "zero recall" in May. The Dongfeng Honda "Rating Engine" vehicle CR-V started a large number of recalls in May with 130,455 recalls, accounting for 15.80% of the total recalls.

FAW-Volkswagen was the most recalled brand in May with 659,049 recalls, accounting for 79.80% of the total recalls. Mainly related to Audi A4 Allroad, A5, A6L, A4L and Q5 and other models. The main reason for the recall is that there may be two failure modes for the engine-assisted coolant pump: 1. The auxiliary coolant pump may be blocked by the foreign matter and cause overheating; 2. The water vapor in the auxiliary coolant pump may cause a short circuit in the internal circuit. Causes the local coolant temperature of the auxiliary coolant pump to be too high and corrodes the relevant parts. In severe cases, it may cause a fire in the engine compartment and there is a safety hazard.

The defective parts of the recalled vehicles in May mainly include engines, airbags, transmissions, and vehicle controllers. Among them, Dongfeng Honda's "oil throttle" that has made a lot of noise since the beginning of the year has finally achieved results. This recall has reached 130,455 units, second only to FAW-Volkswagen. The recall announcement revealed that since May 22, 2018, Dongfeng Honda has recalled some 2018 CR-V models equipped with 1.5T engines, which were produced from February 14, 2017 to February 27, 2018. Dongfeng Honda will replace the air-conditioning control unit and upgrade the FI-ECU software for the vehicles in the recalled area. It will also replace the radiator water pipe assembly and upgrade the TCU software on the models equipped with the CVT gearbox to prevent the increase of the oil level and eliminate safety hazards. . At the same time, when the recall was implemented, the engine oil within the target area was replaced with engine oil and oil filter for free, and engine cleaner was added.

It is understood that Dongfeng Honda's recall activity was carried out under the condition that the State Market Supervision Administration initiated a defect investigation. For some time, the Defective Product Management Center of the State Market Supervision Administration received complaints from consumers about this issue. After receiving the complaint, the State Market Supervision Administration immediately deployed the Defective Product Management Center to conduct defect investigations and assessments of the above issues. Affected by the investigation, Dongfeng Honda Automobile Co., Ltd. decided to take recall measures to eliminate safety hazards. The State Market Supervision and Administration Bureau stated that it will continue to organize defective product management centers to carry out key supervision and evaluation of the measures taken in this recall and requested Dongfeng Honda Automobile Co., Ltd. to be highly responsible to consumers and increase the recall completion rate. Enhance the monitoring of recalled vehicles and effectively protect the rights and interests of consumers.

As for the specific situation, Gasgoo Automobile has conducted comprehensive statistics according to the recall data of AQSIQ, which is organized as follows:

Attachment: Details of domestic car recalls in May (ranked by the number of recalls in each batch)

1. FAW-Volkswagen recalls 659,049 Audi A4 Allroad, A5, A6L, A4L and Q5

Recall range :

From June 6, 2018, the following vehicles were recalled, a total of 659,049 vehicles.

(a) A total of 20,278 Audi A4 Allroad and 2012-2014 Audi A5 cars from November 7th, 2011 to November 8th, 2013 were imported from FAW-Volkswagen Automotive Co., Ltd. for production.

(II) A total of 638,771 Audi A6L and 2013-2014 Audi A4L and Audi Q5 models were produced for some 2012-2015 sections of FAW-Volkswagen Automotive Co., Ltd. from May 3, 2011 to January 17, 2016.

Recall reason :

Some of the vehicles in this recall range may have two failure modes for the engine auxiliary coolant pump: 1. The auxiliary coolant pump may be blocked due to foreign matter; 2. The water vapor in the auxiliary coolant pump may cause a short circuit in the internal circuit. Causes the local coolant temperature of the auxiliary coolant pump to be too high and corrodes the relevant parts. In severe cases, it may cause a fire in the engine compartment and there is a safety hazard.

Solution :

FAW-Volkswagen Automotive Co., Ltd. will commission Audi's distributors to replace the improved auxiliary coolant pumps for vehicles within the recall scope in three batches according to the plan, eliminating potential safety hazards.

2. Dongfeng Honda recalls 130,455 units of CR-V

Recall range:

From May 22, 2018, some 2018 CR-Vs equipped with 1.5T engines, which were produced from February 14, 2017 to February 27, 2018, were recalled for a total of 130,455 vehicles.

Recall reason:

For some vehicles within the scope of this recall, due to design reasons, the engine oil level will increase when the vehicle continues to travel at a short distance in a low temperature environment, and the engine fault light will light up if the oil level rises to a certain extent. Continuous operation of the vehicle in a state may cause damage to the engine and pose a safety hazard.

solution:

Dongfeng Honda Automobile Co., Ltd. will replace the air-conditioning control unit and upgrade the FI-ECU software for the vehicles within the recalled area, and replace the radiator water pipe assembly and upgrade the TCU software for the models equipped with the CVT gearbox to suppress the increase of the oil level. Eliminating security risks.

3. Dongfeng Motor recalled 13,128 Dongfeng Fengshen AX7

Recall range:

From May 18, 2018, a total of 13,128 Dongfeng Fengshen AX7 cars were recalled from October 18, 2017 to March 9, 2018.

Recall reason:

For some vehicles within the scope of this recall, due to suppliers' manufacturing reasons, there is a defect in the press-fitting process of the rear shell sealing ring of the brake vacuum booster assembly. The brake fluid pressure may cause the deformation of the seal ring to deform and fall out. Under extreme conditions, the vehicle may suffer from brake drag and acceleration and weakness, which may cause safety hazards.

solution:

Dongfeng Passenger Vehicles will conduct a free inspection of the vehicles in the recalled area and replace the defective vacuum booster with an improved vacuum booster assembly to eliminate potential safety hazards.

4. FAW Group recalls 8,620 Pentium X40s

Recall range:

Since May 22, 2018, part of the Pentium X40 passenger cars that were produced between October 27, 2017 and April 26, 2018 has been recalled, totaling 8,620 vehicles.

Recall reason:

Vehicles in this recall range may have abnormal safety due to flaws in the controller program of the vehicle. After the remote function of the mobile phone is used, the vehicle may be abnormally extinguished during driving. Under extreme conditions, there is a risk of vehicle accidents and there are potential safety hazards.

solution:

China FAW Group Co., Ltd. entrusted FAW Car Co., Ltd. to inspect and upgrade vehicle controllers for free within the scope of the recall in order to eliminate potential safety hazards.

5. Jiangling Motors recalled 7,180 Jiangling Ford New Generation Transit

Recall range:

From May 5, 2018, a total of 7,180 vehicles were recalled for some of the new Jiangling Ford Transit vehicles produced between August 1, 2015 and July 31, 2016.

Recall reason:

Some vehicles in the recalled area did not use the tooling to ensure the clearance between the crankshaft position sensor and the flywheel when the operator assembled the engine. As a result, the crankshaft position sensor of the individual vehicle contacted with the flywheel and was worn out. As a result, the flywheel signal could not be read. The engine fault light would Lights, in extreme circumstances may cause the vehicle to turn off the engine while driving, and there are potential safety hazards.

solution:

Jiangling Motors Co., Ltd. will check and replace the crankshaft position sensor for the vehicles in the recall area free of charge to eliminate potential safety hazards.

6. Alfa Romeo (Shanghai) recalls 2,799 vehicles from Stevie

Recall range:

From May 18, 2018, recalled imported 2017 and 2018 Alfa stelvio cars from March 3, 2017 to January 25, 2018. According to the statistics of the company, 2,799 vehicles were involved in the Chinese mainland.

Recall reason:

Vehicles within the scope of this recall may be damaged due to water entry due to improper control of the sealing process in production. The harness of the body control module (BCM) or the connection between the BCM and the car body A column may be damaged due to water ingress; the same batch of vehicles may be improperly controlled due to the sealing process during production. The harness connector and the electric tailgate switch button inside the door outer cover may be damaged due to water seepage.

solution:

Alfa Romeo will conduct free seal optimization to eliminate defects for the body control module (BCM) involved in the recall of the vehicle and the wiring harness between the BCM and the body A pillar, as well as the interior of the electric tailgate outer cover. Inventory vehicles will also be sold after eliminating hidden dangers.

7. Tianjin FAW Toyota, Toyota (China) recalled Corolla (Hybrid) and Lexus RX 1,726 vehicles

Recall range:

Toyota Motor (China) Investment Co., Ltd. has expanded its recall of the following vehicles to a total of 1,726 vehicles, as follows:

(i) Tianjin FAW Toyota Motor Co., Ltd. has recalled Corolla (hybrid) cars produced from January 16, 2016 to February 3, 2016 starting from May 28, 2018, with 1,416 vehicles;

(2) As of July 1, 2018, Toyota Motor (China) Investment Co., Ltd. has recalled Lexus RX cars that were manufactured from October 22, 2015 to October 29, 2015, and the number was 310.

Recall reason:

In the recalled vehicles in this area, the airbag control system was equipped with a batch of acceleration sensors. The production conditions of the IC chips in the batch of acceleration sensors were not appropriate, resulting in the possibility that some IC chips may be broken during the use of the vehicle. As a result, the airbag warning light is lit and the airbag fails to deploy properly. This poses a safety hazard.

solution:

Tianjin FAW Toyota Motor Co., Ltd. and Toyota Motor (China) Investment Co., Ltd. will check the production number of the airbag acceleration sensor for the vehicle assembly in the recall range, and replace the acceleration sensor belonging to the batch in question with qualified parts for free. To eliminate security risks.

8. Ford (China) recalls 1,177 Ford F-150s

Recall range:

Because of potential safety hazards in the transmission shift cable fixing device, from May 24, 2018, recalled 1,177 vehicles imported from June 6, 2017 to November 25, 2017 (including) for 2018. -150 Raptor car.

Recall reason:

The reason for this recall is that the clips fixed to the transmission on shifting cables on some affected vehicles may not be properly installed. With long-time operation, a clip that is not properly installed or disengaged may result in the driver not being able to reach the correct gear. In this case, when the driver parks at the P position and stops and stops, the instrument panel will not be able to warn that the vehicle is not properly engaged in the gear. If no parking brake is applied, the vehicle may be accidentally moved in some cases. Hidden danger.

solution:

Ford China’s authorized dealers will check whether the shifting cable fixing clips are properly installed on the vehicles in the recall range, and adjust the cables and clamps according to the inspection conditions to eliminate hidden dangers.

9. Beijing Benz recalls 860 E-Class

Recall range:

From May 25, 2018, a total of 860 E-class automobiles were produced during the period from July 12, 2016 to June 22, 2017.

Recall reason:

In the E-class vehicle with a long wheelbase partially equipped with a rear-side airbag in the recall range, the main harness may be squeezed by the rear-side airbag holder and damage the harness. As soon as the harness breaks, part of the vehicle's functionality will be affected. If the power of the fuel pump is interrupted, the vehicle will lose power; if the harness of the responsible side airbag, side airbag or rear seatbelt tensioner is damaged, the related protection function will be affected; if a short circuit of the harness is caused, it cannot be ruled out There is a safety hazard in the risk of fire.

solution:

Beijing Benz Motors Co., Ltd. will apply blankets to the side airbag brackets of vehicles within the scope of recall to prevent the bracket from coming into contact with the wiring harness, and inspect the wiring harness. If it is damaged, repair it to eliminate potential safety hazards.

10. Suzuki (China) recalls 305 vehicles in Kaisei

Recall range:

From July 1, 2018, some of the 2012-2015 models were imported for the importation of the Jersey vehicles, with production dates from November 16, 2012 to December 15, 2015. According to the company's statistics, 305 vehicles were involved in the mainland China.

Recall reason:

The reason for this recall is that the circuit board of the continuously variable transmission (hereinafter referred to as CVT) controller is equipped with a resistance element. Due to the abnormality of this resistance element, the solenoid valve that regulates the CVT oil pressure will not work properly, resulting in an increase in oil pressure. If it rises, it triggers the operation of the CVT protection mechanism. Eventually it may cause the vehicle speed to decrease and speed up the difficulty in the course of driving. There is a potential safety hazard.

solution:

Suzuki (China) Investment Co., Ltd. will replace the modified CVT controller for the vehicles within the recall scope to eliminate potential safety hazards.

11. Anhui Jianghuai recalled 286 trucks

Recall range:

Since May 10, 2018, some Jianghuai trucks have been recalled, involving a total of 286 vehicles. details as follows:

(i) A total of 191 JAC trucks were produced during the period from May 2014 to January 2017.

(2) A total of 31 JAC trucks were produced during the period from January 2016 to September 2016.

(III) A total of 42 JAC trucks were produced during the period from July 2016 to March 2017.

(d) A total of 22 JAC trucks were produced during the period from February 2016 to February 2017.

Recall reason:

In the above-mentioned range (1), due to the non-standard paste of reflective signs, there is a deviation in the range and area of ​​reflective light, and the requirements of the relevant standards are not met, and there are potential safety hazards during night driving.

In the above range (II), due to manufacturing problems of some suppliers, the size of the protective device does not meet the requirements of the relevant standards. In the event of a vehicle collision, it may not be able to effectively play a protective role and there is a potential safety hazard.

In the above range (3), due to manufacturing problems, some vehicles do not have position indicator lights installed, and at night or in poor road lighting conditions, they may not be able to display the outline of the vehicle, fail to meet the requirements of the relevant standards, and have potential safety hazards.

Within the scope (4) of the above-mentioned range, due to manufacturing problems of some suppliers, the tail sign plates were not installed, and there was a deviation in the reflective range of the vehicles, which did not meet the requirements of the relevant standards, and there were hidden safety problems.

solution:

For the above-mentioned range (1) Anhui Jianghuai Automobile Group Co., Ltd. will inspect the vehicles within the scope of the recall, and freely paste or re-apply reflective signs to eliminate potential safety hazards.

For the above scope (2) Anhui Jianghuai Automobile Group Co., Ltd. will inspect the vehicles within the scope of recall, and replace the protective devices that meet the requirements of the standard free of charge to eliminate potential safety hazards.

For the above-mentioned range (III) Anhui Jianghuai Automobile Group Co., Ltd. inspected the vehicles within the scope of the recall, and provided free installation of profile lights to eliminate potential safety hazards.

For the above scope (4) Anhui Jianghuai Automobile Group Co., Ltd. will inspect the vehicles within the scope of the recall, and freely install the tail sign board to eliminate potential safety hazards.

12. Shenlong Automobile recalls Citroen C4 Picasso 141

Recall range:

From May 31, 2018, the imported Citroën C4 Picasso series cars were recalled from January 18, 2017 to April 6, 2017. According to company statistics, a total of 141 vehicles were involved.

Recall reason:

In the recalled area, due to the position and width of the glass glue that adheres to the inner and outer plates of the engine hood, the adhesion of the inner and outer plates of the hood may not be met, and the hood may be shaken or deformed. In extreme cases, the degumming of the inner and outer plates of the hood and the outer plate of the hood may be caused, which may cause safety hazards.

solution:

Shenlong Automobile Co., Ltd. will provide free maintenance for the vehicles in the recall scope, and add glass glue between the inner and outer panels of the hood in accordance with the specification to eliminate potential safety hazards.

13. Dongfeng Motor recalls Lotus brand 6-meter children's special school bus 65

Recall range:

From May 22, 2018, some of the Lotus special 6m children's school buses that were produced from March 31, 2015 to November 1, 2016 were recalled, totaling 65 vehicles.

Recall reason:

The side-opening safety doors of some school buses within the scope of this recall have flipped their seats without instructions, causing the user not to know how to turn the seat. In the case of not flipping the seat, the width of the safety passage at the safety door is less than 300 mm, which presents a safety hazard.

solution:

Dongfeng Motor Co., Ltd. will provide free training for users of vehicles in the recalled area to guide users to correctly use the flip-up seat; and stick the instructions for use on the flipped seat to eliminate potential safety hazards.

14. Yangzhou Yaxing Bus recalls Yaxing YBL6121H1QP bus 51

Recall range:

Since May 15, 2018, a total of 51 YBL6121H1QP buses have been recalled from November 1, 2015 to March 31, 2018 (inclusive).

Recall reason:

Vehicles in this recall scope have problems with the matching degree of the steering trapezoidal mechanism between the vehicle and the steering axle. During the full-load state of the vehicle, when the power steering fails, the steering force does not conform to the national mandatory standard GB17675-1999 "Automotive steering system. In the basic requirement “3.9, the steering force should be less than 588N when there is power steering but the power steering fails, there is a safety hazard.

solution:

Yangzhou Yaxing Bus Co., Ltd. will replace the vehicles within the recall range with the steering axle assembly improved by the steering trapezoidal mechanism free of charge to eliminate potential safety hazards.

15. Porsche (China) recalls 2 Macan vehicles

Recall range:

From May 30, 2018, some of the 2018 Macan cars were produced during the period from January 22, 2018 to January 23, 2018. According to statistics, a total of 2 vehicles were involved.

Recall reason:

The terminating resistors of the vehicle's gateway control unit may not be soldered properly during this recall, resulting in disruption of the communication between the different control units of the vehicle. All kinds of error messages are displayed in the instrument cluster. In extreme cases, the control performance of the vehicle and some of the protection functions required after the vehicle collision may be affected and there are potential safety hazards.

solution:

Porsche (China) Automobile Sales Co., Ltd. will commission Porsche authorized service centers across the country to replace the qualified gateway control units for vehicles within the recall scope, eliminating potential safety hazards.

16. Ford (China) recalls two Ford F-150 Raptors and Ford Mustangs

Recall range:

From May 18, 2018, recalled one 2017 Ford F-150 Raptor model and 2018 model Ford Mustang 2.3T Performance model car.

Recall reason:

The reason for this recall is that due to the instability of the gearbox automatic assembly system, the insertion step of the parking pawl guide bushing on some of the affected vehicles may be omitted and not installed. If the transmission is repeatedly used in the event of missing pins, the parking function may be lost. Even if the gear and the dashboard indicate that the vehicle has been engaged in the P position, when the driver stops and stops, the instrument panel cannot warn that the vehicle is not correctly engaged in the P position. If parking brake is not applied, it may cause accidental movement of the vehicle in extreme cases, which may cause safety problems.

solution:

Ford China's authorized dealers will check the presence of vehicles within the scope of the recall of the transmission parking pawl guide bushings for defects, and install roll pins as needed to eliminate hidden dangers.